Transmission Type DSG 7 DQ200
Component Complete Mechatronic Unit (Hydraulic Block + TCU)
Condition Used, Tested
TCU Part Number 0AM927769E
Mechatronic Part Number 0AM325025E
Warranty 12 Months
Complete DQ200 Mechatronic Unit This 0AM325025E mechatronic unit is a used, tested assembly for 7-speed DSG DQ200
gearboxes used in Volkswagen Group vehicles. It is supplied complete with both the hydraulic block and the TCU 0AM927769E , ready for installation as a full mechatronics replacement.
OEM Part Numbers
Mechatronic Assembly Number:
0AM325025E
Related Mechatronics / Hydraulic References:
0AM325025D • 0AM325025H • 0AM325025J • 0AM325065N • 0AM325065L • 0AM325065S • 0AM325065T • 0AM325065AB
Always Verify the Exact Part Number Before ordering, compare the OEM number on your original mechatronic unit and confirm it matches 0AM325025E. This listing includes the complete unit — hydraulic block and TCU together — so it is not necessary to source these components separately.
Technical Specifications
Transmission Type:
7-Speed DSG DQ200
Component Type:
Complete Mechatronic Unit
Mechatronic OEM Number:
0AM325025E
TCU OEM Number:
0AM927769E
Condition:
Used, functionally tested
Supplied As:
Complete unit — hydraulic block and TCU included
Clutch Type:
Dry Clutch DSG System
Torque Range:
For DQ200 applications up to 250 Nm
Installation Note:
Programming / adaptation may be required after installation
Warranty Period:
12 Months
Product Description
This 0AM325025E mechatronic unit is a used, tested replacement for selected DSG 7-speed DQ200 gearboxes used in VW Group vehicles. It is supplied as a complete assembly — hydraulic block together with TCU 0AM927769E — and is intended as a direct replacement when the original mechatronic unit has failed.
What This Mechatronic Unit Does
- Controls hydraulic and electronic functions of the DQ200 gearbox
- Manages clutch engagement, gear selection and shift timing
- Processes sensor data and operating parameters via the integrated TCU
- Regulates hydraulic pressure through the mechatronic valve body
- Serves as a like-for-like replacement for a faulty or non-communicating original unit
Important Product Note This is a used, tested unit supplied complete with the hydraulic block and TCU 0AM927769E. Every unit is inspected and checked prior to dispatch, and is covered by a 12-month warranty against functional defects.
Vehicle Compatibility
This mechatronic unit is intended for selected Volkswagen Group vehicles equipped with 7-speed DSG DQ200 transmission. Compatibility for 0AM325025E / 0AM927769E typically depends on part number, software version and gearbox configuration.
Suitable for Selected Models Such As
- Audi A1 / S1
- Audi A3
- Audi Q3
- VW Golf
- VW Beetle
- VW Jetta
- VW Caddy
- VW Passat
- VW Polo
- VW Scirocco
- VW Sharan
- VW Touran
- Škoda Fabia
- Škoda Octavia
- Škoda Superb
- Škoda Yeti
- SEAT Altea / XL
- SEAT Ibiza
- SEAT Leon
Compatibility Check Recommended DQ200 applications can differ by software version, mechatronics configuration and production period. If you are unsure, send us your VIN number together with the part number from your original mechatronic unit for verification before ordering.
Common Fault Codes & Symptoms
A defective DQ200 mechatronic unit can cause gear selection problems, warning messages, loss of communication and emergency running mode. Replacement units may require programming or matching to the gearbox system after installation.
-
No communication Mechatronic unit not responding correctly during diagnostics
-
Gear selection fault Transmission cannot shift correctly
-
Limp mode Gearbox enters emergency operating mode
-
Start inhibition Vehicle may not start if transmission status is not recognized correctly
-
Programming required Replacement unit needs matching or adaptation
- Warning message for gearbox malfunction on dashboard
- Jerking, delayed engagement or unstable shifting behaviour
- Loss of odd or even gear operation depending on system condition
- Fluid leakage or pressure loss from a worn hydraulic block
Diagnostic Note Fault symptoms alone do not always prove that the mechatronic unit is defective, because clutch, wiring or sensor-related problems can produce similar DSG behaviour. Proper diagnosis before replacement is strongly recommended.
Installation & Service Notes
Recommended Steps
- Check the exact OEM number on the original mechatronic unit
- Confirm that the gearbox is a DSG 7 DQ200 version
- Inspect the surrounding clutch and gearbox components before installation
- Install the replacement unit carefully using professional workshop procedures
- Carry out coding, programming or adaptation if required
- Perform a fluid check and top-up as needed for the DSG system
- Perform diagnostic checks and test gearbox operation after installation
Important Installation Note This is a hydraulic and electronic transmission component. Incorrect installation, wrong software matching or incompatible configuration can prevent the gearbox from operating correctly. Installation by a DSG specialist is strongly recommended.
Why Mechatronic Replacement Matters
1. Restores Full Gearbox Control
A properly functioning mechatronic unit is essential for hydraulic pressure control and electronic communication in the DQ200 system.
2. Supports Correct Shifting
The combined hydraulic block and TCU manage clutch engagement and gear selection logic within the DSG transmission system.
3. Helps Resolve Combined Faults
Replacing the complete unit helps resolve both hydraulic and electronic faults in a single repair, without needing to diagnose which component failed.
4. Tested Before Dispatch
Every used unit is checked for correct operation before it leaves our workshop, giving you a reliable, ready-to-fit replacement.
Quality Assurance & Warranty
12-Month Warranty: This used DQ200 mechatronic unit is tested prior to dispatch and supplied with a 12-month functionality warranty under normal operating conditions.
Warranty Coverage Includes:
- Functional defects of the supplied hydraulic block and TCU
- Material or electronic defects under normal use
- Faults present at the time of delivery that are not caused by installation
Warranty Exclusions:
- Incorrect installation
- Improper programming, coding or adaptation
- Damage caused by wiring, clutch or gearbox-related faults unrelated to the mechatronic unit
- Physical damage or misuse
Questions or Need Help?
We can help verify compatibility and advise whether this 0AM325025E mechatronic unit is suitable for your gearbox.
Contact
Important Purchase Information
- Please compare the OEM number on your original unit before purchase
- This is a used, tested unit — includes hydraulic block and TCU 0AM927769E
- Programming, coding or adaptation may be required after installation
- Professional installation is recommended
- Photos are for illustrative purposes only
- Worldwide shipping is available
- If your country is not listed at checkout, contact us for manual order processing
- Please check carefully whether this product matches your vehicle and gearbox version before ordering
